How to Use Different Measurement Units on a PDF
Calibrate the Page
Before you get started, make sure the page is properly calibrated:
- Locate a known length on the page.
- Open the Calibrate tool using one of the following methods:
- From the Command bar, go to Measure > Calibrate.
- From the Scale section of the Measurements tab, click Calibrate.
- If a dialog box with instructions appears, click OK.
- Click the first point of the known length, then click a second point to finish the line. Hold down the Shift key to snap the two points horizontally, vertically or diagonally. When the second point is selected, the Calibration dialog box opens.
- In the Calibration dialog box, enter the distance that the line between these two points represents on the drawing and select the units in which measurements are to be reported.
- Click OK.
The unit of measurement used when calibrating the drawing is now the default for all measurements on that page. Scales, units of measurement and Store Scale in Page are set on a per-page basis.
Separate Units of Measurement
You can set independent units of measurement for Area and Volume. They will exist separately from each other, and the default unit of measurement will be used for linear measurements.
- Click the Measurements tab.
- Select Independent Units.
- Select a unit of measure for Area Unit and Volume Unit.
- To keep this configuration when the PDF is saved, select Store Scale in Page.
If the Store Scale in Page option isn’t available, scroll down to the Options section of the Measurements tab and select Use Embedded Scale.
To recalculate a previously measured area or volume with a newly set unit of measure, just click Recalculate. All measurements on the page are now recalculated with the current units of measurement.
Take Your Measurements
Once the Independent Units are set up, your Area and Volume measurements will use the units of measurement you’ve selected. All other measurements will utilise the unit of measurement selected when calibrating the page.
Partagez avec vos amis :
Prenez-vous encore des notes et des calculs sur papier ?
Prenez-vous encore des notes et des calculs sur papier ? Il peut être plus rapide avec le logiciel PDF Bluebeam Revu.
Confédération Construction lance son nouveau site dédié au technologies digitales. Bluefields y participe
Bluefields soutiens la Confédération dans son ambition de mettre les technologies digitales en avant pour ses membres. Avec Bluebeam Revu logiciel PDF pour la construction, Bluefields apporte un outil abordable et utilisable immédiatement. Le résultat est aussi directement visible. Tout avantage pour les utilisateurs comme les métreurs, préparation chantier, chefs de projets, ...
Quelles Villes et communes utilisent Bluebeam Revu dans l'administration urbanistique & service technique
Vous trouverez une liste des Villes et communes qui utilisent Bluebeam Revu dans leur administration urbanistique & service technique
Archicad - Bluebeam Revu connectivity
Il est possible d’importer des marquages exécutés avec Bluebeam Revu directement dans Archicad. Archicad est un logiciel de conception Bim et Bluebeam est un logiciel PDF idéal pour une meilleure révision des plans par les architectes, les ingénieurs et les parties prenantes.
Bluebeam Revu sur un Mac OS
Bluebeam n'a (plus) de Revu Mac OS, mais pas de souci il ne faut pas nécessairement prendre un PC Windows. Avec une application sur Mac vous exécuter Windows sur le Mac et ensuite Bluebeam Revu.
I can’t unregister my license because my computer crashed, was lost, stolen, or reformatted
Follow the steps for a quick resolution to this issue
How to launch and use Bluebeam Stapler?
Install, launch and use Bluebeam Stapler: tool to combine individual PDF documents into a single PDF.
The Bluebeam Stapler - Making working life a little less complicated
Working on a job that requires numerous PDF files to be collated into one manageable document? It’s easy with Bluebeam Stapler.
Length and Polylength measurements don’t appear in correct units
Your drawing scale is set to meters, but your Length or Polylength measurements appear in millimeters.
Revu fonctionne avec Citrix et autres services Remote
Bluebeam Revu fonctionne dans un environnement Citrix. D'autres forme remote peuvent fonctionner, mais ne sont pas officiellement supportées.
4 October 2020
Lineas uses intensively Mobileforms
Maak je eigen Apps met Mobileforms?
MobileForms : LA solution mobile d’inspection chantier la plus complète
Videopresentatie : Bluebeam Revu voor Vergunningen en openbare werken
Color processing of drawings with Revu
Hulpverleningszone Taxandria – dienst preventie gaat bouwplannen digitaal keuren
Stad Izegem beoordeelt digitaal de bouwplannen met Bluebeam Revu
I want to copy all of my custom Tool Sets, Profiles and Stamps over to another computer…
When I select a measurement tool in Bluebeam Revu, my page turns blue…
How to put multiple A4 drawings to one A0 in Bluebeam Revu?
Collaborating in Studio with teammates who don’t have Revu
How do I make Revu my default PDF viewer?
Adding and Removing Digital Signature Fields
How to Convert DWG files to PDF
How to convert DWG files to open in Revu
Share Tool Sets, Profiles, Stamps
Through the use of Tool Sets, Profiles, and Stamps, Revu users can customize the software to suit their specific needs. Revu makes it easy to share all of these assets, which can be useful for creating a standardized workflow within your organization.
How to import layers from a drawing into another drawing with Bluebeam Revu?
Situation : you worked on a drawing with Revu, added your own markup layers to it. Then you receive a new PDF, a revision with its layers coming from a CAD. Consider that you want to get those layers added to you first drawing. How to proceed?
Revu slow rendering with some documents (PDF) ? Try following steps.
It happens that some vector based documents (plans) make look that Revu takes its time to refresh the document. You should try following steps.
